Relocation relocation,battery in boot

For all electrical questions; Alternators including fitment; Light connections/wiring; Instruments; Gauges; MFA; Heater blower (not coolant related) issues etc etc.
Forum rules
Hints, tips and guides for repair and modification - the FAQ section on the main website is worth checking first for information relating to common faults and technical help. Useful posts and guides will be added to the FAQ http://www.sciroccoregister.co.uk/scirocco-faq
MrD
Posts: 357
Joined: Thu Apr 02, 2009 3:55 pm
fill in the right answer: 10
Location: Cambridgeshire

Re: Relocation relocation,battery in boot

Post by MrD »

Quality ! Cheers Junglist .
If you could send me relevent pages that would be smashing ,won`t be starting this until near end of June.As on hol
But at a guess allowing extra just in case i would think that 5 m of cable will be ample,will need some sort of terminal block/box to connect up the cable to the wires that connect to the battetry up front,that will take 4awg,and various other sizes smaller than 4 awg.,then will also need 2 terminals to connect to the battery in he back . - terminal for 4 awg x 1 + connector 2 x 4awg Can get box for bat for around £15.

My mail for sending cat pages is infoatmgdcarpetcleaners.co.uk ,replace the at with an @ :hugegrin:


6 point cage,Koni`s,lower front brace,rear brace,goodridge hoses,4,2,1,supersprint back box,k+n,kent gs2h,vernier,skimmed and ported head,alloy fuel tank.catch tank,Short shift ,9A soon.
Image
User avatar
Junglist
Posts: 555
Joined: Wed Apr 01, 2009 7:06 pm
fill in the right answer: 10
Location: MANCHESTER

Re: Relocation relocation,battery in boot

Post by Junglist »

Will do soon mate. I'll try to sort it tomorrow. Do you have fax? Sounds like the lot will total £20 to £30 I think, all top notch gear. The 16mmsq cable's equivalent to 5awg but will be higher rated and more flexible and easier to route due to smaller outside diameter. Do you want any eyelet (copper tube lug) terminals crimping onto the cable? 07999370473 if you need to contact me. Regards, Kieran.


Tornado GTII: Koni, Flo-flex, Girling, Weber, K&N, Powerflow, Goodridge, ASA, Yokohama... to fit: stainless 4 branch.
ImageImage
MrD
Posts: 357
Joined: Thu Apr 02, 2009 3:55 pm
fill in the right answer: 10
Location: Cambridgeshire

Re: Relocation relocation,battery in boot

Post by MrD »

No worries mate,will try and get around to making a complete list with measurements etc over the weekend,will prob need a couple of foot of earth with a terminal crimped on the end ,for where i connect to the body,positive lead will be junction box 1 end,then battery terminal on tother .Cheers


6 point cage,Koni`s,lower front brace,rear brace,goodridge hoses,4,2,1,supersprint back box,k+n,kent gs2h,vernier,skimmed and ported head,alloy fuel tank.catch tank,Short shift ,9A soon.
Image
User avatar
Junglist
Posts: 555
Joined: Wed Apr 01, 2009 7:06 pm
fill in the right answer: 10
Location: MANCHESTER

Re: Relocation relocation,battery in boot

Post by Junglist »

PM'd mate.


Tornado GTII: Koni, Flo-flex, Girling, Weber, K&N, Powerflow, Goodridge, ASA, Yokohama... to fit: stainless 4 branch.
ImageImage
Post Reply