Hi I have a problem ov high revs from cold I wouldn't mind but stay high for like 10/20mins...
How can I adjust this?
Cheers rob
Idles ok when warmed up confused agen lol all trouble wiv this car
gt2 cold start sits at 3k :-(
Forum rules
Hints, tips and guides for repair and modification - the FAQ section on the main website is worth checking first for information relating to common faults and technical help. Useful posts and guides will be added to the FAQ http://www.sciroccoregister.co.uk/scirocco-faq
Hints, tips and guides for repair and modification - the FAQ section on the main website is worth checking first for information relating to common faults and technical help. Useful posts and guides will be added to the FAQ http://www.sciroccoregister.co.uk/scirocco-faq
- sciroccof529bax
- Posts: 116
- Joined: Sat Jan 09, 2010 3:23 pm
- fill in the right answer: 10
- Location: wolverhampton /westmidlands
- sciroccof529bax
- Posts: 116
- Joined: Sat Jan 09, 2010 3:23 pm
- fill in the right answer: 10
- Location: wolverhampton /westmidlands
-
ianaudia4
- Posts: 3800
- Joined: Wed Apr 01, 2009 4:35 pm
- fill in the right answer: 15
- Location: Central London and Essex
Re: gt2 cold start sits at 3k :-(
Good news, a nice easy fix. Folk often overlook the basics!
1984 MK2 Havanna brown Storm
1989 MK2 Alpine white Scala injection
2006 Audi A4 3.0TDI quattro (the beast)
1989 MK2 Alpine white Scala injection
2006 Audi A4 3.0TDI quattro (the beast)
- james butler
- Posts: 3004
- Joined: Fri Apr 24, 2009 1:54 pm
- fill in the right answer: 10
- Location: birmingham
Re: gt2 cold start sits at 3k :-(
If it's a carb car This can also be caused by broken or loose engine bay wiring going to a carburettor.
As I had this happen to my car a few years ago on the pooberg carb.
Another reason why I ditched it
As I had this happen to my car a few years ago on the pooberg carb.
Another reason why I ditched it
I dont mind project cars but I HATE SANDING!!!
- sciroccof529bax
- Posts: 116
- Joined: Sat Jan 09, 2010 3:23 pm
- fill in the right answer: 10
- Location: wolverhampton /westmidlands
Re: gt2 cold start sits at 3k :-(
It was a 15amp think it was fuse 18 will dubble check tomoz to make sure it's the fuse for not sure wat it is but it's a black wire to the front of the carb
- james butler
- Posts: 3004
- Joined: Fri Apr 24, 2009 1:54 pm
- fill in the right answer: 10
- Location: birmingham
Re: gt2 cold start sits at 3k :-(
as i said theres a vacuum control valve on the carb thats operated by a circuit that also heats the hedghog in the manifold, a heater element on the front of the carb and then to this solinoid thing.
if i disconected the solinoid the car used to rev up to about 3000rpm because no vacuum could reach the throttle actuator.
the reason for this is too little vacuum makes the actuater on the throttle push the throttle open more than it should at idle.
the reason it does this is at startup the throttle is opened by this actuator untill vacuum builds, then actuator moves off the throttle thus creating an idle speed.
when you switch on electrical loads the engine revs drop slightly and the vacuum drops aswell, this drop in vacuum makes the actuator move and pushes the throttle open to regain the correct idle speed.
to be fair the pooberg carb is a nifty bit of kit, its a shame its a pig to set up properly, or i would put it back on the car instead of the weber.
if i disconected the solinoid the car used to rev up to about 3000rpm because no vacuum could reach the throttle actuator.
the reason for this is too little vacuum makes the actuater on the throttle push the throttle open more than it should at idle.
the reason it does this is at startup the throttle is opened by this actuator untill vacuum builds, then actuator moves off the throttle thus creating an idle speed.
when you switch on electrical loads the engine revs drop slightly and the vacuum drops aswell, this drop in vacuum makes the actuator move and pushes the throttle open to regain the correct idle speed.
to be fair the pooberg carb is a nifty bit of kit, its a shame its a pig to set up properly, or i would put it back on the car instead of the weber.
I dont mind project cars but I HATE SANDING!!!
